Acquiring a Proton Spectrum

This section provides a brief overview how to acquire a 1D 1H NMR spectrum. For this we assume that:

1. OVJ-B12 is installed on the computer
2. The hardware is set up properly
3. A sample is inserted into the probe
4. The NMR probe is tuned to the spectrometer frequency.

Acquiring a ¹H NMR

1. From the protocols tab drag the PROTON experiment into the plotting window, or double click on the PROTON protocol.

   

   Alternatively, the pulse sequence can be set using the OVJ command line:

   1	seqfil='s2pul'

   The PROTON sequence calls a pulse program s2pul. This is a general, two-pulse sequence used to run variety of different experiments such as a single pulse NMR experiment or an inversion-recover sequence.

2. Next, the user has to set the length and power of the RF pulse to properly acquire a 1D ¹H spectrum. In OVJ the pulse parameters can be changed from the OVJ command line or from the acquisition panel.

The length of the observe pulse is given by the parameter pw. From the OVJ command line set the pulse length:

1

pw=3

corresponding to a pulse length of 3 µs.

3. Next some of the acquisition parameters need to be set. Go to the Acquire tab and click on Acquisition. Here, basic acquisition parameters can be adjusted. Alternatively, the values can be entered in the OVJ command line.

   • Spectral Width: Parameter sw
   • Acquisition Time: Parameter at
   • Complex Points: Parameter np

   For example

   1 2	sw=50000 np=4096

   will set the spectral width to 50000 Hz (50 kHz) and the number of points acquired in the time domain to 4096.

4. Set the number of transients (nt) to 4. In general, OVJ will add a CYCLOPS phase cycle to each sequence automatically to remove DC offsets and correct for phase imbalances. Therefore, the parameter nt should always be set as a multiple of 4.

   1

   nt=4

5. On the Acquire tab click Channels to set the transmitter offset tof parameter. To get started, set this value to 0

   1

   tof=0

   With the transmitter offset set to 0, the spectrum, if excited on resonance, appears in the center of the window. To center the spectrum adjust the tof value. Alternatively, you can click with the mouse on the peak (single red line cursor) and enter the command movetof in the OVJ command line. OVJ will automatically adjust tof so that the NMR spectrum in the next acquisition is at the center of the window.

6. Start the acquisition by either pressing the GO button or by typing

   1

   go

   in the OVJ command line. The acquisition will start and the data is displayed and processed on the screen.

Phasing a spectrum

Once the acquisition is finished, the spectrum most likely needs to be phased to show just the real part of the complex spectrum (see figure below). This can be done automatically using the autophase command aph or manually.

Using the Autophase Routine

To autophase the spectrum type the following command in the OVJ command line and press enter:

1

aph

to autophase the spectrum.

Manually Phasing the Spectrum

Sometimes, the autophase routine fails and the spectrum needs to be phased manually. To manually phase an NMR spectrum:

1. Click the Phase button in the toolbar to the left

   

2. Click the spectrum with the left mouse button and keep the button pressed. Two red cursors appear to the left and right of the peak. Phase the peak by moving the mouse up and down. This will adjust the 0^th order phase correction (frequency-independent phase correction). Alternatively, the phase can be adjusted from the OVJ command line by typing:

   1

   rp=11.5

3. To adjust the 1^st order phase correction (frequency-dependent phase correction) click the Phase button in the toolbar to the left. Next, select the peak by moving the mouse cursor to the NMR peak and click the right mouse button. The point selected is the pivot point used to adjust the 1^st order phase correction. By moving the mouse up and down the phase of the rest of the spectrum can be adjusted. To adjust the 1^st order phase correction lp from the OVJ command line type:

   1

   lp=157

The proper phased spectrum is shown below.

Next, proceed to the next section to Save the NMR Spectrum.